AMOLEN3D Printer Filament Storage Bags Vacuum Kit, Filament Bags Storage Spool Sealing 30 Bags with Two Sizes, Dust Proof Humidity Resistant for Keeping Filament Dry

I don't have any issues printing TPUs and this brand is no different. I was so excited when I found a multicolor TPU, I had to try it. This one printed really well. No issues. I printed this on a Bambu X1 with 80mms speeds and 235 temps. Came out perfect. The flexibility was pretty standard, not super flexible but not too stiff. I will buy this again when I run out.Cheers!

I am using it to print these little furbies as buisiness cards for my furby repair shop and it prints like a dream on my Ender 3 V3 SE. The colors are very vivid although they can get a little duller during color transitions. I have almost a full color cycle in the photo, only lacking the reddest part, so the transitions are in there. The only improvement I could see would be having blues and purples but it is lovely as it is. When I run out I will gladly grab some more.

I've had some pretty rough experiences with TPU in the past, especially with the translucent and multicolor stuff, but this has been great.It is just slightly harder and has a little less stretch than some of the others I have used, but it prints easily, and the final product is still plenty flexible enough, and doesn't seem like it'll break during normal use.The stringing it does have is very light and burns away completely with just a quick go-over with a torch, and ends up with some of the cleanest looking TPU prints I've had. I'm planning to buy the other colors from this manufacturer soon.

I saw this in one of my random filament shopping rounds and had to try it.As some other reviewers have stated, you REALLY have to charge objects made from this filament. Really really really charge them. If you don't, you'll be disappointed with little to no glow from your 3D printed objects. In my short experience direct sunlight charges this filament best.As far as printing, no issues for me. I've used my standard settings of 220 degrees at the nozzle, 60mm per minute travel rate, and general .1mm layer height. I do adjust the settings as needed but the amounts I outlined are what I generally use for any PLA.It prints fine. With my settings prints do come off the plate looking a bit rough but I know that's just my complacency in not dialing in settings for this filament. I'm confident that with some effort, prints from this filament would turn out looking wonderful.I do want to note that this filament looks like standard glow-in-the-dark green filament. I thought Amazon had sent me the wrong stuff but when I charged the spool under focused light for a bit, I was corrected by the sight of a blue glow. Again, I stress you must charge up this filament to expect it to glow. In my experience though, the glowing capacity for this is much less than standard glow-in-the-dark green, so don't expect the glow to last very long.

I have used almost a 1/2 a roll printing nothing but geckos. I sent my kids to school with like 40 of these suckers as a harmless prank. Everyone loved it and they commented how good the geckos looked.The color changing is pretty quick, it would rotate back and forth between being gold topped and green topped every 6 geckos I would print. I was also able to bump up the volumetric flow some in Bambu Studio from the Generic TPU profile without any issue since this is "high speed".I already ordered another roll of the same thing so I can do other prints with it.

These bags are exactly what I needed once I started having humidity issues in my studio. After I dry or use a filament it goes right in the bag with some desiccant and up on the shelf ready for its next use. I have had a few bags fail to seal and air leaks back in, which is unfortunate but for the most part this is a huge benefit to my work process.This was actually my second order, the first one came with a rechargeable vacuum that makes it very easy to use and convenient. I’m not sure that the little moisture indicators actually work as all the circles stay blue whether they are sitting out in the open, dipped in water or sealed up tight.

I haven’t really messed with any other brands of TPU so I can’t can’t compare it but I really enjoy printing with this brand. Just temper to run your machine slow and take the time to dial in your settings.

The PLA by AMOLEN was easily printable, the results were pretty nice as you can see. Maybe set the flowrate up a notch. I used the matte olive Filament to print some hiking/outdoor equipment, likean emergency whistle. It fits my military gear perfectly, though youshould not expose PLA to UV-light over long time. I would recommend this, if you are searching for an affordable matte olive PLA, thathelps you create an authentic military finish.

J'ai utilisé la couleur Soie Métal Rainbow Multicolor pour imprimer mon vase et un dragon, je suis vraiment ravi par le rendu des couleurs, le vase est magnifique, avec de jolies reflets, suivant la luminosité il brille🤩.Imprimé avec une buse de 0.8 est une hauteur de couche de 0.36, en mode vase.Le dragon est très bien imprimé, car pas évident comme impression, on voit la qualité du filament. Ma fille l'adore.Imprimé avec une buse de 0.4 est une hauteur de couche de 0.12.J'ai été tenté aussi par la couleur mat armée pour imprimer mon tank, belle couleur mat.Je vais faire d'autre véhicules de l'armée avec👍.Imprimés sur CR10S PRO.L'accroche sur le plateau est très bonne, les impressions sont très bien passées avec la buse à 200°, le plateau à 50°, pour une vitesse à 50mm/s pour les deux filaments.Les couleur et le rendu sont super🤩, la qualité est au rendez vous👌.Voir les photos, les détails sont très bien ressortis.L'emballage est bien.L'enroulement est très bien, je n'ai pas eu de nœuds pendant les impressions.Il suffit de visiter leur boutique pour voir un choix de filaments de qualités.Le reste de leur gamme me donne envie.Je vous conseil ces filaments, je suis content de cette marque👍.La livraison a été rapide.

Alles klar

ottimo con penna £Dvari colori anche fluo,interessanti i color oro e argento che sono metallizzaticonfezione corrisponde a foto24 colori come da fotoconfezionati ognuno sottovuotoconsegna immediata

Hola , el producto es bueno , pero como todo material fosforescente hay que dejarlo cargar , yo uso una linterna a pilas uv ( luz negra ) y el resultado Es muy bueno ,no dura eternamente, yo he cargado 1 hora y más o menos ha tardado 1,5 horas en apagarse, pero se ha imprimido bien y funciona bien , comparar con las manecillas de un reloj de los antiguos para ver lo que brilla y veréis que la calidad es buena , adjunto fotos